Wednesday, 23 November 2011 17:05

How to Work With Active Grille Shutters on a 2012 Ford Focus

Written by I-CAR
Rate this item
(0 votes)

When making collision repairs to the 2012 Ford Focus, be aware that the vehicle may be equipped with an active grille shutter system. This motorized system is located in front of the radiator, which places it in a vulnerable position during front-end collisions.

The active grille shutter system consists of a shutter assembly and an actuator motor. The assembly includes the housing, shutters, retainer, and a wiring harness. Active grille shutters are serviced as an assembly, the shutters are not serviceable individually. The actuator can be serviced individually.


This controlled vent system is primarily designed to maximize fuel economy by reducing drag on the vehicle. The grille shutters automatically close to block airflow through the cooling system when not needed. Closing the active grille shutters helps to improve aerodynamics at high speeds. The shutters open to reduce underhood temperatures when needed. The grille shutter system is also used to control coolant temperatures, HVAC performance, and exhaust emissions depending on the vehicle speed.


The shutters are linked together, with one of the individual shutters attached to the actuator by the retainer. When the grille shutter actuator moves, it moves the attached shutter, which in turn, causes the other linked shutters to move.


The shutters are regulated by the powertrain control module (PCM), and can be set into 16 different positions, from fully closed, to fully open, depending on the amount of cooling air required. The grille shutter actuator receives the position commands from the PCM. The PCM determines the required positions based on inputs such as vehicle speed, coolant temperature, ambient air temperature, and air conditioning system pressure.


During normal operation, the grille shutters are fully open when the engine is off. When starting the engine from cold, the grille shutters will remain closed as long as possible to help reach the most efficient operating temperatures more quickly. This also helps reduce fuel consumption and emissions.

Damage Analysis
The grille shutter assembly is located at the front of the vehicle behind the boron-alloyed steel bumper reinforcement (see Figure 1 again). The bumper reinforcement has crushboxes that attach to the front lower rails. If the crushboxes collapse during a collision, the bumper reinforcement could be forced into the grille shutter assembly.


When analyzing damage, look for obstructions in the shutters that would prevent proper operation of the system. Since all of the shutters are linked together, all it would take is one obstruction to cause a bind. This could be a broken piece of a part or a foreign object. The grille shutter system has a dedicated fuse, and an obstruction may cause the fuse to blow. Also, check that the grille assembly is properly aligned in the opening.


Automatic Calibration
When the engine is started, an automatic calibration of the grille shutter system takes place. This calibration process cannot be initiated manually. Calibration typically takes about 15–20 seconds. The process occurs until calibration is successful, or a fault is detected. Any failure of the system for over 10 seconds continuously will result in the actuator positioning the shutters fully open. There is no indication to the driver when a grille shutter system fault is present, however, a diagnostic trouble code is set in the PCM.

The 2012 Ford Focus may be equipped with the active grille shutter system. Located in the front of the vehicle, the system is in a vulnerable position during frontal collisions.


Except for the actuator, no parts of the system can be serviced individually. When repairs are required, the active grille shutters, housing, retainer, and wiring harness must be replaced as an assembly.


The Ford Focus and the active grille shutter system is one of many 2011-2012 vehicles and systems featured in I-CAR’s instructor-led (live) course, Collision Repair for Ford and Lincoln Vehicles (FOR05).


This course will provide you with an understanding of several of Ford’s vehicle-specific parts and procedures and help you gain an understanding of how maintaining Ford quality repairs can be key to customer satisfaction and achieving a complete and safe repair. Visit the I-CAR website to find a class near you.


For comments or suggestions on the Advantage Online, please contact I-CAR at advantage@i-car.com.

Read 16076 times Last modified on Friday, 13 January 2017 23:16